Don't underestimate the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are several crashes entailing forklifts.

Case 1: The forklift cargo blocked the driver's sight, and the person in front could not be located, resulting in a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when raising heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost causes an crash.
Instance 4: Forklift is speeding and rolls over throughout a turn.
Instance 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the vehicle driver is crushed when the forklift rolls over.
Situation 7: The forklift vehicle driver did not use a seat belt and dropped from the automobile when it surrendered and was crushed.
Forklift procedure need to take notice of these issues ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a tons, the chauffeur needs to first validate that the load is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, take care that there will be no challenges overhead. When the load is taking a trip, the fork has to not be raised too expensive, which will certainly affect the security of the forklift. .
3. After unloading, the fork must be decreased to the typical driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal needs to be issued first. High-speed doglegs are banned. High-speed doglegs will cause the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the load should be in the lowest position that does not hinder the driving, and the gantry ought to be correctly tilted back. The load shall not be raised except when piling or filling. .
8. The elevation of the load must not block the motorist's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility area is 5 km/h, and it should drive safely at a reduced rate when going into the production workshop location. .
11. When the forklift is raised, lifted or driven, it is forbidden for employees to depend on the fork to hold products and play a balancing duty. .
12. If issues are discovered, they will be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or use a fork top or pull. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and unloading things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Be careful not to roll the wheels on the dunnage, so as not to stretch the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as possible under the tons, and it needs to be noted that the fork idea should not touch other items or objects. The tons needs to be supported with marginal back tilt of the gantry so that the tons does not glide in reverse. The mast can be tilted onward slightly when the tons is reduced to permit easy placement of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and ram hard objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Straining is banned, and it is forbidden to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork structure.
2. Draw the hand brake take care of to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for special situations, such as the motorist does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water must be included.
2. Inspect the safety performance of beginning, running and stopping.
3. Check whether the lights and horn signals are complete and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leakage should additionally be Stand-on Electric Pallet Stacker inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you run into a person in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo need to be 0.3 m ~ 0.4 m above the ground;.
5. The turning must not be as well sharp to stop the tendency of "free switching";.
6. Adding and down the slope should be sluggish and consistent, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the gradient is greater than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and move on, if they come across huge or heavy items and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" must be followed in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and other harmful chemicals with forks.
5. It Stand-on Electric Pallet Stacker is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping force to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to service the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive laterally on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roads, train crossings;.
2. Areas with a longitudinal incline more than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844